Passer au contenut Passer au menu de navigationt
Vous ne pouvez passer une commande en ce moment, veuillezNous joindre pour obtenir de l’aide
Spinner
802537
  • EverFlow
  • Module Dessiccateur
  • À vendre
  • Marché secondaire (nouveau)
Comparer

999999 En stock

Spinner

Poids et dimensions

Poids brut
24.38 Kilogram
Poids net
24.38 Kilogram
Longueur
266.7 Millimeter
Largeur
625.6 Millimeter
Hauteur
389.4 Millimeter

Codes VRMS / Explication

013-010-421 Module - Continuous Flow, Air Dryer
Air Dryer Configuration
AD-IS / AD-IS (EverFlow) 
Montage
.676 IN x .40 IN (4x) 
Orifice d'alimentation
1/2-14 NPT X 1/2-14 NPT (Union Tee) 
Governor Unloader Port
3/8-18 NPT x 1/2 PTC (45° Elbow) 
Governor Reservoir Port (Remote Charge)
1/8-27 NPT x 1/4 Tube (Compression / 90° Elbow) 
Governor Control Port
1/8-27 NPT X 1/4 Tube (Compression / Straight) 
SEC Reservoir Port
1/8-27 NPT X 1/4-18 NPT (90° Elbow / Extended) 
PRI Delivery (Reservoir) Port
1/4-18 NPT 
PRI Delivery Opening Pressure
103 PSI 
SEC Delivery (Reservoir) Port
1/4-18 NPT 
SEC Delivery Opening Pressure
109 PSI 
AUX 1 Delivery Port 1
1/4-18 NPT 
AUX 1 Delivery Port 2
1/4-18 NPT 
AUX 1 Delivery Port 3
1/4-18 NPT 
AUX 1 Delivery Port 4
1/4-18 NPT 
AUX 1 Delivery Opening Pressure
109 PSI 
AUX 2 Delivery Port
1/4-18 NPT 
AUX 2 Delivery Opening Pressure
109 PSI 
Purge Exhaust Port
Standard 
Purge Volume
Standard 
Purge Valve Type
Soft Seat 
Pression d'ouverture valve de sécurité
153 PSI 
Power Harness Connector Type
Weather Pack 2-Way Sealed Connector (Female) 
Heater / Thermostat Rating
12V / 90W 
Type de connecteur chauffage
Metri-Pack 280 Series 2-Way Sealed Connector (Male) 
Heater Connector Color
White 
Type de cartouche
Standard 
Filetage cartouche
M39 x 1.5-6H RH 
Clearance to Remove Cartridge
1.00 IN 
Avec régulateur
Yes 
Governor Type
Non-Adjustable 
Pression d'enclenchement
105 PSI 
Pression de déclenchement
130 PSI 
Température d'admission maximale
160 °F (71 °C) 
Température de service mini. [°C]
-40 °F (-40 °C) 
Mise(s) en garde
Do not replace PG cartridge with Standard/GC cartridge. 

Veuillez accepter la déclaration de protection des données et l’exclusion de responsabilité du téléchargement

Disclaimer

The information contained in documents found on this website is intended for the exclusive use of trained persons within the commercial vehicle industry, and must not be passed on to any third party.

All recommendations regarding products and their servicing or usage are with reference to Knorr-Bremse products and should not be considered applicable to products from other manufacturers.

This information does not purport to be all-inclusive and no responsibility is assumed as a result of its use. We cannot accept any liability nor offer any guarantee regarding data accuracy, completeness or timeliness. The information does not represent any guarantee or ensured characteristics of the Products or Systems described.

No liability can be accepted based on the information, its use, recommendations or advice provided. In no event may we be held liable for any damage or loss except in the case of willful intent or gross negligence on our part, or if any mandatory legal provisions apply.

Any legal disputes arising from the use of this information shall be subject to German law.

Note: If service work is carried out on a vehicle as a result of information taken from a document, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.

This disclaimer is an English translation of a German text, which should be referred to for all legal purposes.