Skip to content Skip to navigation menu
You cannot place an order at this time, pleaseContact Us for further assistance
Spinner
K162935
  • AD-HF
  • Air Dryer
  • For Sale (Restricted)
  • Original Equipment
Compare

999999 In Stock

Spinner

Weights & Dimensions

Length
302.0 Millimeter
Width
295.0 Millimeter
Height
266.0 Millimeter

VMRS Codes / Description

013-010-252 Air Dryer W/Drain Valves
Air Dryer Type
Stand-Alone 
Mounting
Purge Reservoir - M12 x 1.75-6g Studs (4x) 
Supply Port
1/2-14 NPT 
Governor Unloader Port
1/8-27 NPT (Plugged) 
Governor Reservoir Port
1/8-27 NPT (Plugged) 
Compressor Unloader Port
1/4-18 NPT (Plugged) 
Remote Charge / Fill Port (through Desiccant)
1/4-18 NPT (with Test Point Connector) 
Remote Charge / Fill Port 1 (after Desiccant)
1/4-18 NPT (with Schrader Valve) 
Remote Charge / Fill Port 2 (after Desiccant)
1/4-18 NPT (with Safety Valve) 
PRI Delivery Port 21
1/4-18 NPT 
PRI Delivery Opening Pressure
103 PSI 
SEC Delivery Port 22
1/4-18 NPT 
SEC Delivery Opening Pressure
112 PSI 
AUX 1 Delivery Port 1
1/4-18 NPT 
AUX 1 Delivery Port 2
1/4-18 NPT 
AUX 1 Delivery Port 3
1/4-18 NPT 
AUX 1 Delivery Port 4
1/4-18 NPT 
AUX 1 Delivery Opening Pressure
112 PSI 
AUX 2 Delivery Port
1/4-18 NPT 
AUX 2 Delivery Opening Pressure
103 PSI 
Purge Exhaust Port
Standard (with Adapter / Silencer) 
Purge Volume
Standard 
Purge Valve Type
DLU (Hard Seat) 
Safety Valve Opening Pressure
153 PSI 
Heater / Thermostat Rating
12V / 90W 
Heater Connector Type
Metri-Pack 280 Series 2-Way Sealed Connector (Male) 
Heater Connector Color
White 
Cartridge Type
PuraGuard (Coalescing) 
Cartridge Thread
M41 x 1.5-6H RH 
Clearance to Remove Cartridge
1.00 IN 
Governor Included
Yes 
Governor Type
Non-Adjustable 
Cut-in Pressure
105 PSI 
Cut-out Pressure
125 PSI 
Pressure Protection Valve Configuration
4 in Parallel 
Reservoir Diameter
Ø 10.2 IN 
Reservoir Length
4.35 IN 
Reservoir Material
Aluminum 
Number of Compartments
Reservoir Fill Type
Integral Fill 
Maximum Inlet Temperature
160 °F (71 °C) 
Minimum Operating Temperature
-40 °F (-40 °C) 
Cautionary Note(s)
Non-serviceable clamp band. Do not remove. 
Please accept the privacy notice and the download disclaimer

Disclaimer

The information contained in documents found on this website is intended for the exclusive use of trained persons within the commercial vehicle industry, and must not be passed on to any third party.

All recommendations regarding products and their servicing or usage are with reference to Knorr-Bremse products and should not be considered applicable to products from other manufacturers.

This information does not purport to be all-inclusive and no responsibility is assumed as a result of its use. We cannot accept any liability nor offer any guarantee regarding data accuracy, completeness or timeliness. The information does not represent any guarantee or ensured characteristics of the Products or Systems described.

No liability can be accepted based on the information, its use, recommendations or advice provided. In no event may we be held liable for any damage or loss except in the case of willful intent or gross negligence on our part, or if any mandatory legal provisions apply.

Any legal disputes arising from the use of this information shall be subject to German law.

Note: If service work is carried out on a vehicle as a result of information taken from a document, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.

This disclaimer is an English translation of a German text, which should be referred to for all legal purposes.