Ir al contenidot Ir al menú de navegaciónt
No puede hacer un pedido en este momento,comuníquese con nosotros para más ayuda
Spinner
5011321
  • AD-IS
  • Secador de aire
  • Se vende
  • Equipo original
Comparar

999999 En stock

Spinner

Peso y dimensiones

Peso bruto
11.79 Kilogram
Peso neto
11.79 Kilogram

Códigos VRMS / descripción

013-010-252 Air Dryer W/Drain Valves
Tipo de secador de aire
Stand-Alone 
Montaje
Purge Reservoir - 3/8-16 UNC-2B (4x) 
Boca de alimentación
1/2-14 NPT 
Boca de descarga del Governor
1/8-27 NPT 
Boca del embalse del Governor
3/8-18 NPT 
Boca de salida PRI 21
1/4-18 NPT 
Presión de apertura de salida PRI
103 PSI 
Boca de salida SEC 22
1/4-18 NPT 
Presión de apertura de salida SEC
103 PSI 
Boca de salida AUX 1 1
1/4-18 NPT 
Boca de salida AUX 1 2
1/4-18 NPT 
Boca de salida AUX 1 3
1/4-18 NPT 
Boca de salida AUX 1 4
1/4-18 NPT 
Presión de apertura de salida AUX 1
103 PSI 
Boca de salida AUX 2
1/4-18 NPT 
Presión de apertura de salida AUX 2
109 PSI 
Boca de escape de purga
Standard 
Volumen de purga
Standard 
Tipo de válvula de purga
Soft Seat 
Presión de apertura de la válvula de seguridad
153 PSI 
Clasificación del calentador / termostato
12V / 90W 
Tipo de conector de calentador
Metri-Pack 280 Series 2-Way Sealed Connector (Male) 
Color del conector del calentador
White 
Tipo de cartucho
Standard 
Rosca de cartucho
M39 x 1.5-6H RH 
Espacio para quitar el cartucho
1.00 IN 
Governor incluido
No 
Configuración de la válvula de protección de presión
4 in Parallel 
Diámetro del calderín
Ø 9.0 IN 
Longitud del calderín
4.00 IN 
Material del calderín
Steel 
Número de compartimentos
Tipo de llenado del calderín
External Fill 
Temperatura máxima de entrada
160 °F (71 °C) 
Temperatura mínima de funcionamiento [° C]
-40 °F (-40 °C) 
Nota (s) de advertencia
Pressure protection valve configs are not interchangeable. 

Acepte el aviso de privacidad y la cláusula de exención de responsabilidades de descarga

Disclaimer

The information contained in documents found on this website is intended for the exclusive use of trained persons within the commercial vehicle industry, and must not be passed on to any third party.

All recommendations regarding products and their servicing or usage are with reference to Knorr-Bremse products and should not be considered applicable to products from other manufacturers.

This information does not purport to be all-inclusive and no responsibility is assumed as a result of its use. We cannot accept any liability nor offer any guarantee regarding data accuracy, completeness or timeliness. The information does not represent any guarantee or ensured characteristics of the Products or Systems described.

No liability can be accepted based on the information, its use, recommendations or advice provided. In no event may we be held liable for any damage or loss except in the case of willful intent or gross negligence on our part, or if any mandatory legal provisions apply.

Any legal disputes arising from the use of this information shall be subject to German law.

Note: If service work is carried out on a vehicle as a result of information taken from a document, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.

This disclaimer is an English translation of a German text, which should be referred to for all legal purposes.